rafiqq rahim

As experienced QA/QC Inspector I'm suitable for this role because my knowledge in refer standard for ASME, API, AWS & BSEN is brilliant. My attitude toward my work is considered good and I can work with all levels. I'm 3.1 welding CSWIP and I have good knowledge in welding procedure and NDT.

QA/QC INSPECTOR (STRUCTURE), YONGNAM ENGINEERING SDN BHD, MALAYSIA

JAN 2019- PRESENT

PROJECT: JTC WOODLANDS NORTH COAST, SHIMANO, ROCHESTER PARK, PUNGGOL

• Reviewed ITP (Inspection Test Plan), Inspection Requirement project
• Checked and witnessed Fit-up Inspection and Dimension inspection before weld 
• Perform Visual inspection according to project standard 
• Conducted WQT, Pre Qualified Welder Test 
• NDT (Non Destructive Test) – Identified, Monitoring, Review Reports – MPI / UT
• Liaise with fitter supervisor for Dimensional Check of levelness, straightness, tolerance based on spec and project procedure
• Conducted inspection and liaise with ITA, RTO and Client
• Highlighted on Quality Issue such as NCR (Non-Conformance Report), Quality Summons to production department 
• Compiled and produced fit-up inspection report, visual inspection report and NDT report 
• Produced manufacturer data record and Inspection release note for releasing product
• Update all daily report (MVR, FIT-UP, VISUAL AND NDT)
• Final Documentation Reviewed for completion of project

QC INSPECTOR (PIPING), ROTARY ENGINEERING LIMITED, SINGAPORE

DEC 2017 - NOV 2018

PROJECT: TANK FARM 5 PROPYLENE BULLET TANK STORAGE AND ITS FACILITIES OILTANKING

• Identified documentation- project specs and code, project procedures, pipe and instrument diagram drawings, project standards
• Reviewed ITP (Inspection Test Plan), Inspection Requirement project
• Monitoring and inspection Storage Raw Material, Valve Consumables
• Site Inspection based on procedure and project spec before, during and after weld
• Monitoring and Inspection during Fabrication and Installation
• Conducted WQT, Pre Qualified Welder Test 
• Material Receiving Inspection – document, cert, visual inspection based on spec
• NDT (Non Destructive Test) – Requested, Monitoring, Review Reports – MPI / RT
• Monitoring Work Progress to meets planning schedule of project planning
• Check pipe identification, size, code and standard before weld
• Inspect fit-up condition such as bevel preparation, bevel type, mismatch, root gap, root face, cleanness & alignment according specification acceptance criteria
• To monitor welding process to ensure every parameter are according to approved WPS
• Conduct Testing and liaise with third party – Hydro Test, Leak Testing, Service Test, Air Blowing Test, Flushing    test 
• Inspect valves as per P&ID drawing and isometric
• Line check refer as P&ID drawing and isometric
• Witness Hydrostatic test, flushing and air blow
• Update all daily report (MVR, FIT-UP, VISUAL AND NDT)
• Updating Drawing as built drawing, Red Line Drawing, Mark Up Drawing, STQ latest issue drawing, update with any site modification
• Final Documentation Reviewed for completion of project

NDT TECHNICIAN, ENERGY WORKFORCE SDN BHD, PENGERANG MALAYSIA

JULY 2015 - NOV 2017

PROJECT: PETRONAS RAPID BULLET TANK(DFPF)

• Perform Assistant Phase Array Ultrasonic Testing
• Perform Hardness Test (VICKER and BRINELL) 
• Perform Magnetic Particle Inspection and evaluate the defects
• Perform Dye penetration inspection and follow procedure given by level III
• Quality control will determine and communicate which parts will be inspected.
• Calibrated NDT tools such as magnetic yoke current and effectiveness to find any defect
• Perform after repair inspection
• Review PAUT, HT and MPI procedure 
• Produced and submitted report for HT, DPI and MPI 
• Communicated and follow up with level III if any problem with work or reporting

Diploma in mechanical engineering at polyethnic Malacca

CSWIP IN MAGNETIC PARTICLE INSPECTION

Attended CSWIP Ultrasonic Testing

Attended CSWIP Radiographic Interpretation 

Attended CSWIP Dye Penetrant Inspection

CSWIP 3.1 WELDING INSPECTOR